SkyLink am-100 Manual de usuario

P/N. 101A365JULY, 2005PATENTED©2005 SKYLINK GROUPHome Smart Centerwww.skylinkhome.comCUSTOMER SERVICE17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1

6. For models with multiple languages,select the desired language basedon the setting below.[ 1 ] - German[ 2 ] - Spanish[ 3 ] - French[ 4 ] - English

Enter master 3 beeps for validpassword to password. 1 longprogramming mode beep for invalidpassword.[1] - Master password[2] - Secondary password[3] -

Phone Number ProgrammingYou can program up to 5 Emergency Phone Num bers. When the system is in panic,the control panel will call these phone numbers

Note:- It’s not recommended to program 911, fire station or any emergency services phone numbers into any of the phone memories without their approva

TM–12–Window / Door Sensor is used to monitor doors or windows thatopen and close. When these doors / windows are open orclosed, the sensors will tra

Insert BatteryUndo the screw on the back of the motion sensor andremove the battery cover. Connect a 9V alkaline batteryto the battery connector. Ple

Caution:When installing the motion sensor, avoid placing it near heat or cold producingdevices (i.e. A/C or furnace vents, fans, ovens, space heaters,

OPERATIONNote:- Each zone can program up to 2 sensors. There are 5 zones, so up to 10 sensors can be programmed to the control panel. Please refer

MuteWhen the alert beeping becomes undesired, you can terminate the beeping in 3different ways:1. Mute button - Manual mute by pressing themute button

The control panel continuously monitors the system status as well as all thesensors status. It will monitor occurrences such as triggered sensors, lo

Home Smart CenterUSER'S INSTRUCTIONSEnglish

Note:- The control panel cannot be armed if there are triggered sensors. Make sureall sensors are in closed position, i.e. (close all doors, windows,

Disarming a triggered control panelIf "System Panic" is announced from the control panel after it has been disarmed,that means the alarm was

–20–OPERATIONPanicPressing the panic button on the controlpanel or keychain remote will cause thesiren to sound and outgoing calls willbe made to the

When sensor failure occurs, try the following:1. Check if the sensor is located at where it should be, and whether there is anyphysical damage to the

Keychain RemoteThe battery of the keychain remote (Alkaline, Type 23A, 12V) needs to be replacedwhen either one of the followings occurs:1. The LED on

Receiving the Emergency CallIf you are on the list as one of the recipients of the emergency call, you should readthe following instructions carefully

Remote Operation by TelephoneThe control panel can be operated while you are away from home. You canhave access to the control panel with any touch t

Table 1: Remote Phone OperationsCOMMUNICATIONSYSTEM OPERATIONPHONE COMMANDDESCRIPTIONTurn on device x[x] = 1 to 5Turn off device xx = [1 to 5]Check sy

ADVANCED PROGRAMMINGAdvanced Programming allows users to customize the control panel to reactdifferently under different conditions. Features such as:

IMPORTANT SAFETY INSTRUCTIONSWhen using your telephone equipment, basic safety precautions shouldalways be followed to reduce the risk of fire, elect

–2–IC Statement‘’This product meets the applicable Industry Canada technicalspecifications.”Before installing this equipment, users should ensure that

–3–CONTENTIntroduction...4Overv

–4–INTRODUCTIONOverviewCongratulations on your purchase of a Skylink Home Smart Center. This is acomplete wireless system which not only functions as

INTRODUCTION–5–• One AC adapter• One telephone cord• Batteries for all sensors- 1 PC 9V Alkaline Battery (PS-101)- 1 PC 12V Alkaline Battery Type 23A(

INTRODUCTION]16151. Zone LEDs2. Numeric Keypad3. Arm button4. Status button5. Mute button6. Panic button7. Power LED8. Arm LED9. Program LED10. System

INSTALLATIONInstalling the ConsoleYou must first determine where the control panel will be located. Please followthe criteria below to select the ide